Length converter

Meters to feet.

Express a room-scale metric length in decimal feet and a familiar feet-and-inches reading.

Meters (m)Inch fraction precision

2.4 m = 7.874016 ft

Nearest inch fraction≈ 94 1/2 in

Fraction rounding difference+0.3 mm

Metric length2,400 mm

Feet and inches7 ft 10.4882 in

The marker shows the fractional part of one inch. This diagram illustrates tick positions; it is not a physical-size ruler.

Reverse conversion ↔Measure on screen ↗

Conversion formula

feet = meters ÷ 0.3048

Enter the source length above. The result updates immediately. These calculations use exact length definitions: 1 m = 100 cm = 1000 mm, 1 in = 25.4 mm, and 1 ft = 12 in. Only the displayed answer and fractional ruler mark are rounded. The feet-and-inches output splits a length into whole feet and remaining inches; decimal feet do not encode an inch count.

Worked example

2.4 m is approximately 7.874016 ft, or 7 ft 10.4882 in. It is not exactly eight feet. An 8 ft ceiling is 2.4384 m high, a difference of 0.0384 m, or 38.4 mm. This is why a rough conversion should not replace a clearance check.

Conversion table: m → ft

Select a source value to load it into the calculator. Decimal results are displayed to at most six places; inch fractions in this table are rounded to 1/16 inch.

Meters → Feet
Meters (m)	Feet (ft)	Nearest inch fraction
	0.328084	≈ 3 15/16 in
	1.64042	≈ 19 11/16 in
	3.28084	≈ 39 3/8 in
	4.92126	≈ 59 1/16 in
	6.56168	≈ 78 3/4 in
	7.874016	≈ 94 1/2 in
	8.2021	≈ 98 7/16 in
	9.84252	≈ 118 1/8 in
	16.404199	≈ 196 7/8 in
	32.808399	≈ 393 11/16 in

When to use this conversion

Use this for room heights, product dimensions, travel descriptions of short distances, and imperial plans interpreted from metric measurements. The converter works with the international foot. It does not transform floor area from square meters into square feet.

If the answer is needed in feet and inches, use the separated output instead of reading the decimal digits as inches. To reverse-check the decimal-foot result, multiply it by 0.3048 and compare with the original meter value.

Exact conversion versus a ruler reading

The unit relationship is exact, but a measured object may have uncertainty. At 1/16 inch, the maximum rounding difference is half a tick: 1/32 inch, or 0.79375 mm. The calculator shows the actual rounding difference for your value. Use a finer division only if the source measurement and physical instrument support that precision.

Next steps

Numerical conversion needs no display calibration. Comparing a physical object against your screen does. Use the ruler for small objects, a verified paper ruler away from your display, or an appropriate calibrated instrument for safety-critical measurements.

Measure on screen Printable ruler PDFs Screen calibration guide How to read a ruler

Related converters

Feet to meters.Convert a foot-based length into meters for metric forms, room plans, or dimensional comparisons.Meters to millimeters.Convert a larger metric length into the fine units used on a cutting list or engineering drawing.Meters to centimeters.Bring room-scale or fabric measurements into the centimeter units found on a tape measure.Meters to inches.Translate a metric length into decimal inches, then choose a fractional tick only if the job permits rounding.Centimeters to feet.Read a centimeter length as decimal feet or as whole feet plus the remaining inches.

Length converters ↗

Reference: NIST unit conversion factors. Calculations use the international foot, not historical survey-foot units. Fractions are explicitly approximate. NIST ↗